ICI Caldaie MONOLITE 120 GT Installation, Use And Maintenance Manual Download Page 3

Page: 3 / 36

General information

General information

INTRODUCTION

Dear Customer,
Thank you for having chosen an appliance of the series

MONOLITE GT

, a high quality and efficiency product, reliable and safe.

We recommend entrusting its maintenance to

Professionally Qualified Personnel

who, when necessary, uses original spare parts.

This manual contains important information and suggestions that must be observed for easier installation and best possible use
of the appliance.

IMPORTANT

Failure to observe the instructions in this manual will void the warranty conditions.

RANGE

BOILER

MODEL

CODE

MODEL

CODE

MONOLITE 120 GT

81037120

17010208

MONOLITE 420 GT

81037420

17010207

MONOLITE 140 GT

81037140

17010208

MONOLITE 555 GT

81037555

17010193

MONOLITE 180 GT

81037180

17010205

MONOLITE 700 GT

81037700

17010193

MONOLITE 250 GT

81037250

17010205

MONOLITE 780 GT

81037780

17010194

MONOLITE 320 GT

81037320

17010206

MONOLITE 850 GT

81037850

17010194

COMPLIANCE

MONOLITE GT

boilers comply with the following European Directives:

–

European Regulation on Gas Equipment GAR 2016/426/EU

–

Low Voltage Directive 2014/35/EU

–

Electromagnetic Compatibility Directive 2014/30/EU

–

Efficiency Directive 92/42/EEC.

Models up to 400kW comply with the Ecodesign of Energy-using Products Directive 2009/125/EC and with the delegated
Regulation (EU) no. 813/2013.

0461

Summary of Contents for MONOLITE 120 GT





































Search results

Summary of Contents for MONOLITE 120 GT

Reviews:

Related manuals for MONOLITE 120 GT

Brands by name

Popular brands

ICI Caldaie MONOLITE 120 GT, Installation, Use And Maintenance Manual

Search results

Summary of Contents for MONOLITE 120 GT

Reviews:

Related manuals for MONOLITE 120 GT

Brands by name

Popular brands