manualshive.com logo in svg

icetro ISI-300TA, User Manual

Share
Download
icetro ISI-300TA User Manual Download Page 25

25

Controlling the speed of making ice cream

Screw Adjust

'a'

1. By adjusting 'Screw Adjust' at the bottom of the lever (out lever), you can 
    adjust the out-speed of the soft ice cream. As shown in the figure on the left, 
    release the 'Screw Adjust' to increase the out-speed of the soft ice cream.

2. As shown in the figure on the right, fasten the 'Screw Adjust' to
     reduce the out-speed of the soft ice cream.

※

After setting up the adjustment bolt position, tighten the set nut‘a’to fix the

    'Screw Adjust' position and maintain constant dispensing volume.

For your 

information

●

 If you release the Screw Adjust to increase the out speed of the soft ice cream, then the 

ingredients in the mixing tank will be supplied to the cylinder relatively slowly. Suddenly, 
the soft ice cream may no longer come out. Therefore, you are recommended to adjust 
the vending speed for one cup every 6 to 8 seconds.

Summary of Contents for ISI-300TA









































Reviews:

No comments

Brands by name

Popular brands

Load more brands