IC Realtime DVR704MSGV5 User Manual Download

Page: 68 / 144

Figure 4-56

4.9.6

Alarm

You can follow the steps listed below to set.

a) You can connect the external alarm port from the rear panel of the device. Usually the

vehicle left-turn, right-turn, brake and door signal information and etc can be input to the

device via the alarm input device.

b) In the main menu, from Setting to Alarm, you can see alarm setup interface. See Figure

4-57.

c) This series product support 6-channel level alarm information. You can set its actual

alarm name such as left-turn, right-turn on the Alarm Name item. Check the Overlay

button, you can overlay corresponding alarm information on the record file.

d) If the alarm signal is 12V/24V voltage, the trigger type shall be h igh valid. If the alarm

signal is ground signal, the trigger type shall be low valid.

e) The normal open means the alarm signal is usually disconnect, system can generate an

alarm when the alarm signal closed. The normal close means the alarm signal is usuall y

connect, system can generate an alarm when the alarm signal disconnected.

You need to set for each alarm channel on the Alarm in item if the device has connected

several alarm channels.



Alarm in: Here is for you to select channel number.



Event type: There are two types. Local input/network input alarm.



Local input alarm: The alarm signal system detects from the alarm input port.



Network input alarm: It is the alarm signal from the network.



Enable: Please you need to highlight this button to enable curr ent function.



Type: Normal open or normal close.



Trigger: Here is for you to set activation mode. There are two options: High/low.



Alarm name: You can input customized name here.



Overlay: Please highlight the box here to enable this function. It can overlay alarm

information on the video screen when an alarm occurred.



PTZ activation: When an alarm occurred, system can activate the PTZ operation such as

preset x.



Anti-dither: Here you can set anti-dither time. The value ranges from 5 to 600s. The

anti-dither time refers to the alarm signal lasts time. It can be seem as the alarm signal

activation stays such as the buzzer, tour, PTZ activation, snapshot, channel record. The stay

time here does not include the latch time. During the alarm process, the alar m signal can

Summary of Contents for DVR704MSGV5

















































































































































Search results

Summary of Contents for DVR704MSGV5

Reviews:

Related manuals for DVR704MSGV5

Brands by name

Popular brands

IC Realtime DVR704MSGV5, User Manual

Search results

Summary of Contents for DVR704MSGV5

Reviews:

Related manuals for DVR704MSGV5

Brands by name

Popular brands