IC Realtime DVR704MSGV5 User Manual Download

Page: 17 / 144

Name

Port name and indicator light

of WIFI function supports

this function.

Remote control receiver

It is to receive the signal from the remote control.

Device lock/unlock (on/off

button)



Please unlock the device before you remove the HDD

box. Otherwise system is going to shut down

automatically.



System can not boot up once the button is unlock.

Please lock the device first and the boot up the device. It

is to save the HDD.

2.2 Rear Panel

2.2.1

Rea Panel

The rear panel is shown as in Figure 2-2.

Figure 2-2

Please refer to the following sheet for front panel button information.

Name

Function

3G1 antenna port

Please note only the unit of 3G module

supports this function.

3G antenna port

WIFI antenna port

Please note only the unit of WIFI module

supports this function.

WIFI antenna port

3G2 antenna port

Please note only the unit of dual-3G

module supports this function.

The second 3G antenna port.(It

is for duak-3G mode only).

GPS port

Please note only the unit of GPS module

supports this function.

GPS port

Summary of Contents for DVR704MSGV5

















































































































































Search results

Summary of Contents for DVR704MSGV5

Reviews:

Related manuals for DVR704MSGV5

Brands by name

Popular brands

IC Realtime DVR704MSGV5, User Manual

Search results

Summary of Contents for DVR704MSGV5

Reviews:

Related manuals for DVR704MSGV5

Brands by name

Popular brands