IBM SureMark 4610 1NF Page 62 Hardware Service Manual Download | Manualshive

Page: 62 / 112

background image

b. Locate the connector and push in on the two release tabs on either side of the connector while

pushing it up and out of the mount.

5. Remove the two screws securing the fiscal base from the printer:

a. Position the printer upright on a work surface with the front of the printer facing you.

b. Remove the two mounting screws from either side and place them in a safe place for future use.

6. Remove the fiscal base from the bottom of the printer.

Installing the fiscal base

This section provided information on how to install the fiscal base on a fiscal printer. For information on
how to remove the fiscal base from a fiscal ready printer see “Fiscal base” on page 69 in Appendix A,
“1NF fiscal ready printer,” on page 69.

To install the fiscal base on a fiscal printer, complete the following steps:

1. Place the frame of the printer on to the fiscal base.

2. Insert the two screws through the mounting holes on the rear of the printer and secure the fiscal base

to the bottom of the printer frame.

3. Orient the printer so that it is upside down.

B

A

Figure 23. Remove the bottom fiscal base from the printer.

Removing and replacing FRUs

48

SureMark Hardware Service

«
...
60
61
62
63
64
...
»

Summary of Contents for SureMark 4610 1NF

















































































































Reviews:

No comments

Related manuals for SureMark 4610 1NF

EasyCoder 501 SA

Brand: UBI Pages: 214

Brand: UBI Pages: 64

imageRUNNER 4570

Brand: Canon Pages: 154

Brand: Citizen Pages: 80

Brand: Make Mendel Pages: 29

Brand: BIO RAD Pages: 61

Brand: Oki Pages: 3

Brand: Xerox Pages: 2

8200DX - Phaser Color Solid Ink Printer

Brand: Xerox Pages: 2

Brand: Planmeca Pages: 56

Brand: Xprinter Pages: 40

Brand: Oki Pages: 239

Brand: Infotec Pages: 72

B-510DN - Business Color Ink Jet Printer

Brand: Epson Pages: 2

C117001-N - DFX 5000+ B/W Dot-matrix Printer

Brand: Epson Pages: 229

AcuLaser CX28 Series

Brand: Epson Pages: 328

B-310N - Business Color Ink Jet Printer

Brand: Epson Pages: 4

C094001 - FX 870 B/W Dot-matrix Printer

Brand: Epson Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands