manualshive.com logo in svg

IBM SureMark 4610 1NF, Hardware Service Manual

Share
Download
IBM SureMark 4610 1NF Hardware Service Manual Download Page 83

Appendix A. 1NF fiscal ready printer

This section contains information on the IBM SureMark 4610 Model 1NF point-of-sale fiscal ready printer.
The IBM SureMark 4610 Model 1NF point-of-sale fiscal ready printer is a high-performance printer is
based on IBM 4610 technologies, incorporating a fiscal ready solution developed by IBM business partners
world wide having features and components that differ from the 4610 Model 1NF point-of-sale fiscal
printer.

Note:

All other information concerning the general remove and replace operations, and servicing of this
printer is the same as the 1NF fiscal printer. Refer to the appropriate sections in this publication for
information on general remove and replace operations.

Fiscal base

This section provides the information needed to remove and install the fiscal base from a fiscal ready
printer.

Removing the fiscal base from a fiscal ready printer

To remove the fiscal base, complete the following steps:

1. If necessary, remove the fiscal tray from the printer (see “Removing the fiscal tray” on page 28 for

information).

© Copyright IBM Corp. 2010

69

Summary of Contents for SureMark 4610 1NF

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands