manualshive.com logo in svg

IBM SureMark 4610 1NF, Hardware Service Manual

Share
Download
IBM SureMark 4610 1NF Hardware Service Manual Download Page 102

Chinese Class A warning statement

Attention:

This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

Japanese power line harmonics compliance statement

Japanese Voluntary Control Council for Interference (VCCI) statement

Attention:

This product is a Class A Information Technology Equipment and conforms to the standards

set by the Voluntary Control Council for Interference by Technology Equipment (VCCI). In a domestic
environment this product may cause radio interference in which case the user may be required to take
adequate measures.

Korean communications statement

Please note that this device has been approved for business purposes with regard to electromagnetic
interference. If you find this is not suitable for your use, you may exchange it for a non-business purpose
one.

88

SureMark Hardware Service

Summary of Contents for SureMark 4610 1NF

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands