manualshive.com logo in svg

IBM 7131-105, User Manual

Share
Download
IBM 7131-105 User Manual Download Page 44

 3.2 Setting the Address Jumper for a Second 7131 Storage Tower

  

If you are installing a second 7131 Storage Tower:

  

1.  Open the front cover (see Figure 3-1).

  

  

 

  

  

 Figure  3-1. The 7131 Storage Tower Front Cover

  

2.  DANGER

     +--------------------------------------------------------------------+

     ¦ To prevent a possible electrical shock from touching two surfaces  ¦

     ¦ with different electrical grounds, use one hand, when possible, to ¦

     ¦ connect or disconnect signal cables.  (RSFTD004)                   ¦

     +--------------------------------------------------------------------+

  

3.  Verify that the 7131 Storage Tower line cord is unplugged and the SCSI cable is not connected.

  

4.  Remove the 4 screws that fasten the top cover to the 7131 Storage Tower (see Figure 3-2).

  

5.  Lift and remove the top cover from the 7131 Storage Tower.

  

  

 

7131-105 User's Guide

Setting the Address Jumper for a Second 7131 Storage Tower

¦ Copyright IBM Corp. 1995, 1996

3.2 - 1

Summary of Contents for 7131-105


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands