manualshive.com logo in svg

IBM 7131-105, User Manual

Share
Download
IBM 7131-105 User Manual Download Page 100

 5.3.2 Closing the 7131 Storage Tower

  

Use the following procedure to close the 7131 Storage Tower:

  

1.  Put the top cover on the 7131 Storage Tower (see Figure 5-18 in topic 5.3.1).

  

2.  Install and tighten the 4 screws to fasten the top cover to the 7131 Storage Tower.

  

3.  DANGER

     +--------------------------------------------------------------------+

     ¦ An electrical outlet that is not correctly wired could place       ¦

     ¦ hazardous voltage on metal parts of the system or the products     ¦

     ¦ that attach to the system.  It is the customer's responsibility to ¦

     ¦ ensure that the outlet is correctly wired and grounded to prevent  ¦

     ¦ an electrical shock.  (RSFTD201)                                   ¦

     +--------------------------------------------------------------------+

  

4.  Connect the line cord to the power source.

  

5.  Press the power switch to power on the 7131 Storage Tower.  The green LED will illuminate (see Figure 5-17 in topic 5.3.1).

  

6.  Close the front cover.

7131-105 User's Guide

Closing the 7131 Storage Tower

¦ Copyright IBM Corp. 1995, 1996

5.3.2 - 1

Summary of Contents for 7131-105


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands