background image

IBC Technologies Inc. 

VFC 15-150 and VFC 45-225 

supply water temperatures up to 185°F. 
While IBC’s stack temperatures are 
generally within 5°F of the return water 
temperature – even at full throttle, the 
higher return water temperatures 
associated with a 185°F supply call for 
CPVC vent material. However, using 
IBC’s CoolVent™ option – with a 
supplemental 145°F vent limit switch 
located at the base of the heat exchanger, 
the stack temperature at the vent 
connection will be below 149°F (see 
Technical Memo 07-01). 

For long vent runs with higher initial 
exhaust temperature, consider use of 
mixed materials for economy: CPVC for 
the initial run followed by PVC to the 
termination. Ensure appropriate 
transition glue is used. The installer is 
responsible to ensure that sufficient 
temperature loss is allowed for in the 
CPVC section to fall below the limit for 
PVC, taking into account the highest 
possible ambient temperature in the area 
of vent travel (e.g. boiler room, attic 
and/or chase). Watch for further 
guidance on materials combinations: 
IBC will publish and update Technical 
Memo 07-01 on the subject as product 
configurations and 

ULC-S636 

inspection 

practices evolve.  

 USA:

 PVC (Sch. 40 ASTM D1785 or 

D2665 and fittings) or CPVC (Sch. 
40/ASTM F441 with Sch. 80 fittings); or 
CSA approved 3" stainless vent systems. 

For the 

inlet

 air – PVC, CPVC or ABS (all 

Sch.40) are permitted.  

Do not use ABS or any cellular core pipe for 
exhaust venting. 

 

The boiler offers 2” venting connections. 
Fittings are to be used to adapt to the 
appropriate diameter – see 

Vent Travel

 

below. Exhaust venting is to be connected 
directly to the 2” NPT male threaded 

stainless steel fitting on the bottom of the 
pressure vessel using a 2" PVC or CPVC 
threaded adaptor or 90° elbow adaptor. A 
condensate trap formed using the supplied 
fittings shall be spliced into the exhaust or 
near the base of the boiler. See Figure 2. 

Combustion air piping is connected at the 
base of the boiler using a standard 2" PVC 
(ABS) coupler or elbow. Screen material can 
be placed at the inlet as appropriate for the 
environment (e.g. insects, dust).  

Venting shall be supported in accordance 
with applicable code. 

1.4.1.2

 

Vent Travel 

3” CPVC or PVC (Canada: 

ULC-S636 

approved; USA: solid DWV) piping is the 
standard venting option; with this, the boiler 
can be sited up to 120 equivalent feet from 
the vent termination (for the VFC 45-225 

with nat.gas only,

 up to 240’ equivalent). The 

actual vent travel allowance is reduced for 
fittings in accordance with 

Table 3

. – e.g. 

for a VFC 15-150 using 6 x 90º PVC elbows, 
the maximum lineal measure is 90 feet 
(120’–(6 x 8’= 48) = 72’). For the 15-150 
model, vent installations requiring only short 
travel can be satisfied using 2’ or 2½” pipe.  

Table 3 - Max. Venting Length (each side) 

Pipe Size 

Max. Equiv.Length 

  2” (15-150 only) 

  50 feet (each side) 

  2½” (15-150 only) 

  70 feet 

    3" (15-150) 

120 feet 

  3" (45-225 propane) 

120 feet 

  3" (45-225 nat. gas) 

240 feet 

  90° long elbow 

allow 5’ equiv. 

  90° vent elbow 

allow 8’ equiv. 

  45° elbow 

allow 3’ equiv. 

Note such measures pertain separately to 
each the exhaust and intake, but unused 
intake travel cannot be added to the exhaust. 

For 3" piping, a 3"x 2” bushing is to be 
used in the inlet piping within 3 feet of 

Summary of Contents for VFC 15-150


























































Reviews: