IAI CV-M77, Operation Manual

Page: 24 / 32

CV-M77
- 23 -
7.3. Command Protocol
Command Name Format Parameter Remarks
A - General settings and useful commands.
EB Echo back EB=[Param.]<CR><LF> 0 = Echo off 1 = Echo on
Set to 'off' at power on.
VN
Firmware program
version request
VN?<CR><LF>
Response is 3 letter
(ex) 104
B - Timing and shutter related commands.
SM Shutter mode SM=[Param.]<CR><LF>
0 = Normal 1 = Programmable
exposure
Available when
TR=0, TR=1 or TR=3
SH Shutter speed
SH=[Param.]<CR><LF>
0 = OFF(1/25)
1 = 1/50
2 = 1/125
3 = 1/250
4 = 1/500
5 = 1/750
6 = 1/1000
7 = 1/1500
8 = 1/2000
9 = 1/3000
10 = 1/4000
11 = 1/10000
Available when SM=0 and
TR=0 or 1or 3.
PE
Programmable
exposure
PE=[Param.]<CR><LF>
3 - 791 H in 1H increments
3 = 1.5H (0.076ms)
791 = 789.5H (40.107ms)
H = 50.8
µ
s
Available when SM=1 and
TR=0, TR=1 or TR=3
TR Trigger mode
TR=[Param.]<CR><LF>
0 = Normal
1 = Edge pre-select
2 = Pulse width control
3 = EPS Frame delay readout
4 = Long time shutter
5 = PWC Frame delay readout
DR
High Frame Rate
(Draft mode)
DR=[Param.]<CR><LF>
0 = Normal 1 = High frame
rate
Only every third line is read
out
WP WEN polarity WP=[Param.]<CR><LF> 0 = Active_L 0 = Active_L
SY G on SYNC SY=[Param.]<CR><LF> 0 = OFF 1 = ON
EP EEN polarity EP=[Param.]<CR><LF> 1 = Active_H 1 = Active_H
WS WEN/Sync switch WS=[Param.]<CR><LF> 0 = WEN 1 = Sync
C - Gain and analogue signals settings.
AS AGC switch AS=[Param.]<CR><LF> 0 = OFF (Manual) 1 = ON (Auto)
GA Master gain level GA=[Param.]<CR><LF> 0 - 700 Available when AS=0.
RG Red gain level RG=[Param.]<CR><LF> 0 - 255
Available when WB=0.
BG Blue gain level BG=[Param.]<CR><LF> 0 - 255 Available when WB=0.
AG AGC level AG=[Param.]<CR><LF> 0 - 255
Available when AS=1.
WB White balance WB=[Param.]<CR><LF>
0 = Manual
1 = Auto 2 = 4600K
3 = 5600K
Sets manual gain values (RG,
BG) when changed to 0 from
other selections.
AW Auto white balan. AW=[Param.]<CR><LF> 0 = One push auto white balance
Available when WB=1.
SU Master setup level SU=[Param.]<CR><LF> 33 - 223
default = 128
RS Red setup level RS=[Param.]<CR><LF> 96 - 160
default = 128
BS Blue setup level BS=[Param.]<CR><LF> 96 - 160
default = 128
WC White clip level WC=[Param.]<CR><LF> 0 - 1023
GS Gamma select GS=[Param.]<CR><LF> 0 = 1, 1 = 0.45, 2 = 0.6
D - saving and loading data in EEPROM
LD
Load settings
from camera
EEPROM
LD=[Param.]<CR><LF>
0 = FACTORY
DATA
1 = USER DATA
Latest used DATA AREA
becomes default at next
power up.
SA
Save settings
to camera EEPROM
SA=[Param.]<CR><LF> 1 = USER DATA AREA
SA00
Save settings into
Factory Area.
SA00=[Param.]<CR><LF> 0 = FACTORY DATA AREA
Not disclosed for user.
EA
EEPROM Current
Area No. Request
EA?<CR><LF>
0 = FACTORY
DATA
1 = USER DATA
Return latest used area
!! Do not try to use commands not shown in this list.