background image

4

Introduction

 (continued)

This product is designed to be used indoors.

This product is not operable outdoors. Do not expose this 
product to direct sunlight for hours and do not install the

 

product near a heater or an air conditioner. Otherwise, it may 
cause deformation, discoloration and malfunction.
Keep this product away from water and moisture.

i-PRO Co., Ltd. assumes no responsibility for injuries 
or property damage resulting from failures arising out 
of improper installation or operation inconsistent with 
this documentation or through use of parts other than 
this product, such as locally procured parts.

Do not place this product in the following places:

•  Locations exposed to direct sunlight
•  Locations subject to having strong vibration or impact
•  Locations near magnetic field sources such as a 

television or speakers

•  Locations near the devices that emit large sound and 

generate vibration by sound pressure

•  Locations where condensation forms easily, where 

temperature changes greatly or where humidity level is 
high

•  Locations subject to steam and oil smoke such as a 

kitchen

•  Locations which are not level
•  Locations subject to dust
•  Locations where it may get wet from rain or water splash

Do not install this product in locations where the 
product or the cables can be destroyed or damaged 
by persons with malicious intent.

In order to prevent injury, the product must be securely 
mounted to a wall according to Installation Guide.

Place this product horizontally on a level surface.

Do not place this product in an upright position. When 
stacking multiple recorders, clear a space of more than 5 cm 
{2 inches} from both sides, the top, the bottom and the rear 
of the recorders.

More than 

5 cm {2 inches}

More than 

5 cm {2 inches}

More than 

5 cm {2 inches}

More than 

5 cm {2 inches}

•  Do not stack this product in a stack.
•  Do not place anything that can generate vibration on the 

top of this product.

Precautions for installation

To install a hard disk drive in the recorder, it is necessary to assemble an HDD unit (encase the hard disk drive in the HDD 
canister). The HDD unit is designed to easily install/remove the hard disk drive in/from the recorder. Contact your dealer about 
purchasing, installing, and replacing the hard disk drives.

About HDD Unit

Summary of Contents for WJ-HXE410 Series

















Reviews: