background image

Genuine Accessories

8

N
O
T
E

A. Release the Upper Steering Column Shroud using a trim removal tool.
B. Remove the three (3) Phillips Screws securing the Lower Steering Column Shroud as shown.
    - Rotate the Steering Wheel as needed to access the two (2) Upper Screws.
C. Release the Tilt Adjust Lever on the Steering Wheel Column.
D. Carefully remove the Lower Steering Column Shroud to access the 6-Pin Ignition Switch Connector.
E. Adjust the Tilt Steering Wheel to the 

fully extended position

 and lock into place.

F. Store the removed parts in a safe location for reinstallation.

N
O
T
E

#2 Phillips Screwdriver and Trim Removal Tool

Caution: Do not damage the Steering Column Shroud, Steering Wheel, Ignition Switch Connector or Steering Column.
Caution: Make sure that both 6-pin connectors are fully locked together.

7

**NOTE : To access screws, insert key and turn to the ACC position in order to prevent steering wheel from locking.
Caution: Do not damage the Steering Column Shroud, Steering Wheel or Steering Column.

A. Unplug the Factory 6-Pin Female Connector from the Ignition Switch.
B. Plug the Factory 6-Pin Female Connector into the Remote Start 6-Pin Male Connector.
C. Plug the Remote Start Harness 6-Pin Female Connector into the Ignition Switch connector.
D. Make sure the Remote Start Harness is routed as shown.

Phillips 

Screws 

Factory 6-Pin Female 

Ignition Connector 

Factory 6-Pin 

Ignition Connector 

Remote Start 6-Pin 
Ignition Connector 

Revision Date

5/03/2018

Page 5 of 11

Summary of Contents for S2F57 AC300












Reviews: