background image

 

 

User Manual 

This manual is intended for users of the Wi-Fi video doorbell.   

 

Disclaimer 

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY 

AT YOUR OWN RISKS. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL 

OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER 

ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY 

WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.   
 
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR 

JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS 

THE APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS 

USED WITH ILLEGITIMATE PURPOSES.   
 
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER 

PREVAILS. 

 

Regulatory Information 

FCC Information 

Please take attention that changes or modification not expressly approved by the party 

responsible for compliance could void the user’s authority to operate the equipment. 
FCC compliance: This equipment has been tested and found to comply with the limits 

for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against harmful interference when the 

equipment is operated in a commercial environment. This equipment generates, uses, 

and can radiate radio frequency energy and, if not installed and used in accordance with 

the instruction manual, may cause harmful interference to radio communications. 

Operation of this equipment in a residential area is likely to cause harmful interference 

in which case the user will be required to correct the interference at his own expense. 
FCC Conditions 

This device complies with part 15 of the FCC Rules. Operation is subject to the following 

two conditions: 
1. This device may not cause harmful interference. 

2. This device must accept any interference received, including interference that may 

cause undesired operation. 

EU Conformity Statement 

This product and - if applicable - the supplied accessories too are 

marked with "CE" and comply therefore with the applicable harmonized 

European standards listed under the EMC Directive 2014/30/EU, the 

RoHS Directive 2011/65/EU.   

Summary of Contents for HYU-561


















Reviews: