background image

 

 

z

 

Do not aim the device at the sun or extra bright places. A blooming or smear may 

occur otherwise (which is not a malfunction however), and affecting the 

endurance of sensor at the same time. 

z

 

Please use the provided glove when open up the device cover, avoid direct contact 

with the device cover, because the acidic sweat of the fingers may erode the 

surface coating of the device cover. 

z

 

Please use a soft and dry cloth when clean inside and outside surfaces of the 

device cover, do not use alkaline detergents. 

z

 

Please keep all wrappers after unpack them for future use. In case of any failure 

occurred, you need to return the device to the factory with the original wrapper. 

Transportation without the original wrapper may result in damage on the device 

and lead to additional costs. 

z

 

The power supply must conform to LPS. The recommended adaptor models and 

manufacturers are shown as below. Use the attached adapter, and do not change 

the adaptor randomly. 

Model 

Current  Manufacturer 

Standard 

MSA-C1500IC12.0-18P-US  1.5A 

MOSO POWER SUPPLY 

TECHNOLOGY CO.,LTD 

NEMA 

TS-A018-120015AD 

1.5A 

SHENZHEN TRANSIN 

TECHNOLOGIES CO.,LTD 

NEMA 

MSA-C2000IC12.0-24P-US  2A 

MOSO POWER SUPPLY 

TECHNOLOGY CO.,LTD 

NEMA 

ADS-26FSG-1212024EPCU  2A 

SHENZHEN HONOR 

ELECTRONIC CO.,LTD 

NEMA 

MSA-C1500IC12.0-18P-DE  1.5A 

MOSO POWER SUPPLY 

TECHNOLOGY CO.,LTD 

CEE 

ADS-25FSG-1212018GPG 

1.5A 

SHENZHEN HONOR 

ELECTRONIC CO.,LTD 

CEE 

MSA-C2000IC12.0-24P-DE  2A 

MOSO POWER SUPPLY 

TECHNOLOGY CO.,LTD 

CEE 

ADS-24S-121224GPG 

2A 

SHENZHEN HONOR 

ELECTRONIC CO.,LTD 

CEE 

MSA-C1500IC12.0-18P-GB  1.5A 

MOSO POWER SUPPLY 

TECHNOLOGY CO.,LTD 

BS 

ADS-25FSG-1212018GPB 

1.5A 

SHENZHEN HONOR 

ELECTRONIC CO.,LTD 

BS 

MSA-C2000IC12.0-24P-GB  2A 

MOSO POWER SUPPLY 

TECHNOLOGY CO.,LTD 

BS 

ADS-24S-121224GPB 

2A 

SHENZHEN HONOR 

BS 

Summary of Contents for HYU-561


















Reviews: