IM2021
16
Если есть подозрение на утечку, все открытое пламя должно быть удалено / погашено.
Если обнаружена утечка хладагента, которая требует пайки, весь хладагент должен быть
извлечен из системы. Бескислородный азот (OFN) должен затем продуваться через
систему как до, так и во время процесса пайки.
14. Изъятие и вакуумация
При вмешательстве в контур хладагента для проведения ремонта или для любых других
целей должны проводиться обычные процедуры. Необходимо иметь ввиду
легковоспламеняемость хладагента, при проведении данных процедур.
Должны соблюдаться следующие процедуры:
Удалите хладагент;
Продуйте контур инертным газом;
Откачайте газ;
Снова продуйте инертным газом;
Разомкните цепь, с помощью пайки или обрезки
Хладагент должен быть извлечен в специальные цилиндры для извлечения хладагентов.
Система должна быть «промыта» с помощью бескислородного азота (OFN), чтобы
сделать устройство безопасным. Этот процесс может потребоваться повторить несколько
раз. Сжатый воздух или кислород не должны использоваться для этой задачи.
Промывка должна быть проведена путем нарушения вакуума в системе с помощью
бескислородного азота (OFN) и продолжения его заполнения до тех пор, пока не будет
достигнуто рабочее давление, затем выпуск его в атмосферу, затем повторное
вакуумирование. Этот процесс следует повторять до тех пор, пока в системе не будет
полностью
отсутствовать
хладагент.
Когда
используется
последний
заряд
бескислородного азота (OFN), система должна быть сброшена до атмосферного
давления, для обеспечения ее работоспособности.
Эта операция абсолютно необходима перед проведением пайки на трубопроводах.
Убедитесь, что выход для вакуумного насоса не находится вблизи источников возгорания
и имеется вентиляция.
15. Процедура заправки хладагента
В дополнение к обычным процедурам зарядки должны соблюдаться следующие
требования.
-
Обеспечить, чтобы не происходило взаимного загрязнения различных хладагентов при
использовании заправочного оборудования. Шланги или линии должны быть как можно
короче, чтобы свести к минимуму количество содержащегося в них хладагента.
-
Цилиндры для заправки хладагентов должны быть в вертикальном положении.
-
Убедитесь, что система хладагента заземлена до заправки им системы.
-
Промаркируйте систему, когда зарядка завершена.
-
Осторожно следите за тем, чтобы не переполнить систему охлаждения.
Перед перезарядкой системы она должна быть испытана под давлением с помощью
бескислородного азота (OFN). Система должна быть проверена на утечку после
завершения зарядки, но до ввода в эксплуатацию. Последующее испытание на
герметичность должно быть проведено до ухода с места установки прибора.
16. Вывод из эксплуатации
Перед выполнением этой процедуры важно, чтобы специалист полностью знаком с
оборудованием и всеми его деталями. Требуется большой опыт для безопасного
извлечения хладагента. Перед проведением процедуры следует взять пробу масла и
хладагента на случай, если потребуется анализ перед повторным использованием
регенерированного хладагента. Важно, что использовать электричество можно только до
начала процедуры.
Summary of Contents for H-DH20-P83WF
