manualshive.com logo in svg

Hyundai DHY6000SE, Service Manual

Share
Download
Hyundai DHY6000SE Service Manual Download Page 35

Changzhou ITC Power Equipment Manufacturing Co.,Ltd.

Changzhou ITC Power Equipment Manufacturing Co.,Ltd.

Changzhou ITC Power Equipment Manufacturing Co.,Ltd.

Changzhou ITC Power Equipment Manufacturing Co.,Ltd.

Changzhou ITC Power Equipment Manufacturing Co.,Ltd.

POWER PRODUCTS 

32

4.2.4 Piston ring 

(1) Assemble and disassemble the piston ring with a piston ring compressor. 

(2) Face the section with the marks upward while assembling the piston ring. 

(3) Be sure that piston ring rotates smoothly after installation. 

(4) When inserting the helical elastic collar into the oil ring, be sure the joint of the helical 

elastic is at the opposite of the opening of oil ring.     

(5). Space the open points of the piston rings 120 degrees apart.   

4.3 Connecting rod 

4.3.1 Check the connecting rod 

(1). Check distortion of the large and small end holes for being parallel and distortion. Pass 

the measuring jigs through the large end and small end holes of the connecting rod to 

measure if the jigs are parallel or distored. Replace the connecting rod if it distorted beyond 

the permitted limit.   

Parallelism or distortion 

Standard 

Maintenance Limit 

m

m

5

0

.

-

-

5.3.2 Check the crankshaft bushing

(1) Check whether the surface of bushing between the connecting rod and the connecting rod 

neck. Replace the bush if peeling or damage occurred. 

(2). Insert the connecting rod to the shaft neck, and tighten the connecting rod nut with the 

specified tightening torque. 

5.3.3 Connect the piston and the connecting rod 

Adjust the piston position and align the top mark of the piston with the mark of the 

connecting rod as per the below figure. As the result, the top mark of the piston will align 

with the section of the crankcase cover (gear case) when insert the piston into the cylinder 

sheath.   

Summary of Contents for DHY6000SE


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands