background image

3

12

WHAT TO DO IN AN EMERGENCY

!

Raise the car high enough so that the
fully inflated spare tire can be installed.
To do this, you will need more ground
clearance than is required to remove
the flat tire.

D060F02E-AAT

5. Raising the Car

After inserting a wrench bar into the
wheel nut wrench, install the wrench bar
into the jack as shown in the drawing.
To raise the vehicle, turn the wheel nut
wrench clockwise. As the jack begins
to raise the vehicle, double check that
it is properly positioned and will not slip.
If the jack is on soft ground or sand,
place a board, brick, flat stone or other
object under the base of the jack to
keep it from sinking.

   WARNING:

Do not get under the car when it is
supported by the jack! This is very
dangerous as the vehicle could fall
and cause serious injury or death.
No one should stay in the car while
the jack is being used.

7HNF4025

Wrench bar

Wheel nut
wrench

D060E01A-AAT

4. Put the Jack in Place

The base of the jack should be placed
on firm, level ground. The jack should
be positioned as shown in the drawing.

D060E01NF-A

Summary of Contents for 2009 Sonata































































































































































































































































































Reviews: