background image

6

DO-IT-YOURSELF MAINTENANCE

12

HHR5048

(1)

WINDSHIELD WIPER BLADES

G080A02A-AAT

The wiper blades should be carefully
inspected from time to time and cleaned to
remove accumulations of road film or other
debris. To clean the wiper blades and
arms, use a clean sponge or cloth with a
mild soap or detergent and water. If the
wipers continue to streak or smear the
glass, replace them with genuine Hyundai
replacement parts or their equivalent.

!

   CAUTION:

o Do not operate the wipers on dry glass.

This can result in more rapid wear of
the wiper blades and may scratch the
glass.

o Keep the blade rubber out of contact

with petroleum products such as
engine oil, gasoline, etc.

G080B01HR-GAT

Replacing the Wiper Blades

To replace the wiper blades, raise the
wiper to the vertical position.

To remove the wiper blade

1. Push down the wiper blade with the

locking clip (1) pressed to detach it from
the wiper arm.

G080A01NF-A

2. Raise the wiper blade lightly and pull it

up.

HHR5049

Summary of Contents for 2009 Sonata































































































































































































































































































Reviews: