Hypertherm powermax900 Page 44 Operator'S Manual Download

Page: 44 / 73

PERATION

4-3

Operator Manual

OPERATING INSTRUCTIONS

1. Ensure that the work environment and your clothing meet the safety requirements outlined in

the

Safety

section.

2. Follow the instructions in the

Setup

section. Verify that the input gas supply pressure is set to

90 psi (6.2 bar).

3. At the rear of the power supply, set the power switch to the ON (I) position. The POWER ON,

GAS PRESSURE and LINE VOLTAGE LEDs should illuminate green. The TEMP LED should
remain extinguished.

Adjust the gas pressure REGULATOR to read 70 psi (4.8 bar)

on the PRESSURE GAUGE:

•

Pull the REGULATOR CAP out

•

Push the GAS TEST switch in

•

Turn the REGULATOR CAP while still holding in the GAS TEST switch

•

After adjustment to 70 psi (4.8 bar), release the GAS TEST switch

•

Push the REGULATOR CAP back in

Note: If using 50 ft (15.2 m) torch leads, adjust pressure to 75 psi (5 bar).

5. Adjust the AMPS knob to the desired setting. See

Cut Chart later in this section if necessary.

WARNING

Before operating this system, read the Safety section of this manual thoroughly!

PRESSURE GAUGE

Figure 4-2

Powermax900 Operating Indicators and Adjustments

REGULATOR

AMPS

GAS TEST

REGULATOR
CAP

POWER ON

GAS PRESSURE

9-99

Summary of Contents for powermax900










































































Search results

Summary of Contents for powermax900

Reviews:

Related manuals for powermax900

Brands by name

Popular brands

Hypertherm powermax900, Operator'S Manual

Search results

Summary of Contents for powermax900

Reviews:

Related manuals for powermax900

Brands by name

Popular brands