Hypertherm Echion Operator'S Manual Download Page 77

Page: 77 / 194

Preventive maintenance

Echion

Operator

Manual 810770

even

tive maint

enance

21.

Put the needle-and-seal assembly into the valve body until the needle guide is even with the top
of the bore.

22.

Install the actuator on the valve body. Tighten the actuator by hand.

23.

Use a torque wrench to tighten the high-pressure fittings on the valve body. Refer to

High-pressure water fittings

on page 144.

24.

Connect the water drain tube to the bleed-down valve.

25.

Connect the compressed air hose to the fitting on top of the actuator.

26.

Turn

the utility water to the pump.

27.

Turn

the compressed air source.

28.

Turn

the electrical main (line disconnect switch).

29.

Turn the primary breaker disconnect lever on the electrical enclosure door to

30.

Make sure that the EMERGENCY STOP is not engaged. If the button is pushed in, turn the
button clockwise until it releases.

31.

Make sure that the key switch is set to Local

32.

Push the Controls button.

33.

On the operator interface, touch the

symbol to start the pump.

34.

Monitor for leaks.

Summary of Contents for Echion



































































































































































































Search results

Summary of Contents for Echion

Reviews:

Related manuals for Echion

Brands by name

Popular brands

Hypertherm Echion, Operator'S Manual

Search results

Summary of Contents for Echion

Reviews:

Related manuals for Echion

Brands by name

Popular brands