Hypertherm Echion Operator'S Manual Download Page 164

Page: 164 / 194

Installation

164

810770 Operator

Manual

Echion

Inst

alla

Operator interface: Adjustment screens

The adjustment screens on the operator interface let the user change the system configuration.

On the operator interface, touch the adjustments tab to open the primary adjustments screen.

Pump Adjustments

Not all screens are used when installing the pump.

Touch the current screen symbol to go back 1 screen.

Refer to

Touchscreen maps

on page 175 to see all of the screens available on the controller.

Date / Time / Language

Pump Information

Remote Configuration

Start Procedure Timers

Stop Procedure Timers

Pressure Adjustments

Pump Fault Behavior

Summary of Contents for Echion



































































































































































































Search results

Summary of Contents for Echion

Reviews:

Related manuals for Echion

Brands by name

Popular brands

Hypertherm Echion, Operator'S Manual

Search results

Summary of Contents for Echion

Reviews:

Related manuals for Echion

Brands by name

Popular brands