Hypertherm Echion Operator'S Manual Download Page 48

Page: 48 / 194

Operation

810770 Operator

Manual

Echion

Ope

rati
o

Check the low-pressure water pressure gauges

The prefilter water-pressure gauge shows the water pressure before the water goes through the
filter. The postfilter water-pressure gauge shows the water pressure after the water goes through
the filter.

The usual range is 2.8 bar to 7.6 bar (280 kPa to 760 kPa / 40 psi to 110 psi).

Do this task when the pump is operating.

Subtract the value shown on the postfilter water pressure from the value shown on the prefilter
water pressure.

If the difference between the values is more than 0.7 bar (70 kPa / 10 psi), replace the water filter.

Make sure that the emergency stop operates correctly

Do this task when the pump is operating.

On the operation panel, push the EMERGENCY STOP button. Refer to

Emergency stop

page 51.

Replace the water filter:

• every 1,000 hours.

• if the difference between the values is more than 0.7 bar (70 kPa / 10 psi).

Refer to

Replace the water filter

on page 80.

Postfilter water-pressure gauge

Prefilter water-pressure gauge

Summary of Contents for Echion



































































































































































































Search results

Summary of Contents for Echion

Reviews:

Related manuals for Echion

Brands by name

Popular brands

Hypertherm Echion, Operator'S Manual

Search results

Summary of Contents for Echion

Reviews:

Related manuals for Echion

Brands by name

Popular brands