background image

5

714598 rev 4

IRT UVA 1 PrepCure 3 Digital 

GB

 

NOTE

: The restart of a hot lamp normally takes 4-6 

minutes pending on the duration time in the recent 
performed curing.

NOTE

: When the curing process is terminated, do not 

turn off the main switch before the cassette has, by the 
fan, cooled down for about 5 minutes. Switching off 
the dryer too early will shorten the lifetime of the UVA-
lamps.

7.  Maintenance 
 

Before every usage:  

 

Check that 

 

  External cabling is not damaged 

 

  That protection glass in front of lamp is not cracked  

 

  or removed

 

Weekly

Check that UV lamps light up during mobile dryer  
operation.
Also, check that all cables are undamaged. A damaged 
cable can be a danger to life!

 Quarterly

Change the air filter at least once per quarter. If the 
outer surface of the filter becomes very dirty, it must be 
changed sooner.

8.  Filter replacement

1.  Loosen the metal clips on the side plates of the cassette.
2.   Remove the used filter.
3.   Insert the new filter in such a way that the IRT logo is 

visible from the outside.

4.  Push the long edges of the filter into the cassette 

grooves.

5.   Replace the metal clips.

  

Attention: 

 The filters are disposable and so should not 

be cleaned as this will result in the loss of their filtering 
capacity.

9.  UV-lamp replacement

Please contact your distributor and order a UV-
lamp replacementkit including instructions.
 

Reset Lamp timer 

After replacing the lamp a reset of the timer needs 
to be done.

 

Reset Lamp timer: Make sure that the main switch 
[5] is turned off. Hold the Start/Stop button [1] 
and top right button [2] pressed in simultaneously 
while the main switch [5] is turned on. Keep the 
buttons pressed in until a confirmation message 
(L1--rESEt.) appears in the top display [4].

10.  Trouble shooting

 Problem

The UVA lamps starts up but shuts down automatically 
after a while.

Possible solution

The lamp is worn out. Please contact your distributor 
and order a new one. 

Problem

The lamp doesn´t start.

Possible solution 

Ensure that required cooling time for lamps is fulfilled. 
Cooling time increases with dirty air filter.

11.  EC Declaration of conformity

According to testing institutes and according to the 
machine directive the IRT products in this manual are 
not defined as machines, wherefore the machine direc-
tive reference cannot be included in this declaration.

In accordance with EN 17050-1:2010
We, 

Hedson Technologies AB

   

Box 1530

   

SE-462 28  VÄNERSBORG

  

Sweden

declare under our sole responsibility that the product
IRT-UVA 1 PrepCure 3 Digital
to which this declaration relates is in conformity with 
the following standards

EN 60204-1  

Safety of machinery

EN 61000-6-3   Electro-magnetic Compatibility,
 

Generic Emission Standard.

EN 61000-6-2   Electro-magnetic Compatibility,
 

Generic Immunity Standard.

EN 61000-3-2   Electromagnetic Compatibility
EN61000-3-4  

Electromagnetic Compatibility

EN ISO 9001  

Quality Management System

in accordance with the provisions of the following  
directives in their most current version
2014/35/EU  

Low Voltage Directive

2014/30/EU  

Electro-magnetic Compatibility

 Directive
2011/65/EU  

Restriction of the use of certain

 

hazardous substances (RoHS)

Arlöv Sweden, April 21 st 2016

[3]

[5]

[2]

[4]

[1]

Summary of Contents for IRT-UVA 1 PrepCure 3 Digital

































Reviews: