Hyperdyne Labs Vortex 3 Dark Lord Manual Download | Manualshive

Page: 4 / 17

background image

Vortex 3 Voice Effects Unit,



Hyperdyne Labs LLC

4

The Vortex 3 module consists of two board stacks, the upper INTERFACE board stack and the lower
PROCESSING board. The board stacks are sandwiched together using header pins. The boards must not be
separated, as both are necessary for proper operation!

The processing card has female header pins and can be removed from the interface board stack. It is connected via
friction fit. This allows you to use other processing cards with different voice effects loaded onto them.

«
...
2
3
4
5
6
...
»

Summary of Contents for Vortex 3 Dark Lord


















Reviews:

No comments

Related manuals for Vortex 3 Dark Lord

Brand: Lattice Semiconductor Pages: 30

Brand: WAFER Pages: 15

Brand: wattio Pages: 20

Brand: Lawler Pages: 5

Brand: U-Prox Pages: 31

Brand: FrSky Pages: 2

Brand: Cansec Pages: 45

Brand: Cansec Pages: 43

Brand: Cansec Pages: 32

Brand: Lawler Pages: 4

Brand: Hama Pages: 46

Brand: Galcon Pages: 35

Brand: FAAC Pages: 4

Brand: FAAC Pages: 52

Brand: jablotron Pages: 2

Brand: Jabra Pages: 4

Brand: Talgil Pages: 14

Brand: Tadao Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands