Hydrotec HY-MAG DN100 Operating Instructions Manual Download

Page: 6 / 13

- 6 -

The shown current rating is dependent on the type of water conditioning unit.

HY-

MAG

DN20 / 25

235 mA ± 10%

HY-

MAG

DN32 / 40

345 mA ± 10%

HY-

MAG

DN50 / 65

465 mA ± 10%

HY-

MAG

DN100

3.25 A ± 10%

Menu Sequences

Input and programming of HY-

MAG

Integral control box by pressing the front foil buttons

(behind transparent cover) as below:

Retrieval of menu.
Return from the individual menu levels.

Clear parameters.

Selection of individual menu sequences in menu levels, modification
and setting of parameters.

Retrieval of individual menu sequences,
confirmation/acknowledgement of settings

NOTE :

The monitoring returns to Standard Mode if input is delayed for more than 30
seconds and standard operation is shown in the display again.

Main Programme Menu

The individual sub-menus are selected in the main menu. The main menu is reached by

pressing the button

once.

Summary of Contents for HY-MAG DN100














Search results

Summary of Contents for HY-MAG DN100

Reviews:

Related manuals for HY-MAG DN100

Brands by name

Popular brands

Hydrotec HY-MAG DN100, Operating Instructions Manual

Search results

Summary of Contents for HY-MAG DN100

Reviews:

Related manuals for HY-MAG DN100

Brands by name

Popular brands