background image

 

 

- 8 - 

 

Operating Hours 

 
The operating hours of the HY-

MAG

 unit are registered by 2 separate counters.  

 
Absolute value: 

Total operation time of HY-

MAG

 unit in the actual installation.  

(Operation hours since start-up). Standby-times are not registered and 
thus, not shown.  

 
Relative value:  

Operating hours of unit counted from a certain period of time.  
The counter can be reset by the operator. (Operating hours since  
last reset). 

 
The below display is show

n after the main menu sequence “operating hours” is retrieved: 

 
 
 
 

The operator is in a position to reset the relative operating hours by pressing the button 

 

once and the relative operating hours since the last reset are shown in the display.  

The operating hours can be cleared by pressing the button 

 once and the same button 

also is used to return to the previous display.  
 
 
 
 
Clearing the relative operating hours results in an automatic store and monitoring of the 
actual time of clearing in line 2.  
 
 
 
 

Date / Time 

 
The operator can alter the internal timer and the date as described below. The main menu 
Date / Time must initially be retrieved, whereby the display shows the actual setting.  
 
 
 

If the setting is to be altered, press the button  

 . Should no modification be requested, 

the sub-menu can be left by pressing the button 

 
The active field that can be altered is marked with a line underneath. Change the setting by 

pressing the buttons 

 or 

 until the desired figure is visible in the display. The setting 

is finished once the Cursor is not flashing anymore. The mode is achieved by pressing the 

corresponding button 

. The menu can be left by pressing the button 

 once.  

 
 

Oper. hours   abs    000250 
Oper. hours    rel     000015 

000015   oper. hours since

 

08.10.2003    14:50 

000000   oper. hours since

 

10.10.2003    09:40 

Date:        Wed    10.10.2003

 

Time:                    09:45 

Date:        Wed    10.10.2003

 

Time:                    09:45 

Summary of Contents for HY-MAG DN100














Reviews: