manualshive.com logo in svg

HYDROO HDROO Series, Operation Manual, Page: 8 / 9

Share
Download
HYDROO HDROO Series Operation Manual Download Page 8

14

15

Continued

Fault

Cause

Solution

Remarks

Pumped water does 

not flow constantly

a) Suction pipe is too small.

a) Enlarge inlet pipeline

b) There is not sufficient water 

in pump water inlet.

b) Improve system and 

increase coming water

c) Liquid level is Iow.

c) Try to lift liquid level.

d) Pump inlet pressure is too 

low compared with water 

temperature, pipeline loss 

and flow.

d) Improve system and 

try to increase the inlet 

pressure.

e) Suction pipe is partly 

blocked by impurities.

e) Check and clear 

impurities.

Pump runs but gives 

no water

a) Suction pipe is blocked by 

impurities.

a) Check and clean 

suction pipe.

b) Foot valve or check valve is 

closed.

b) Check and repair foot 

valve or check valve.

c) Leakage in suction pipe.

c) Check and repair 

suction pipe.

d) There is air in suction pipe 

or pump.

d) Refill liquid, 

release air.

Pump runs 

backwards when 

switched off

a) Leakage in suction pipe.

a) Check suction pipe

b) Foot valve or check valve is 

defective.

b) Check and repair foot 

valve or check valve.

c) Foot valve is blocked in 

opened or partly opened 

position.

c) Check and repair foot 

valve.

d) There is air in suction pipe.

d) Check and repair 

suction pipe and 

release air.

Fault

Cause

Solution

Remarks

Abnormal vibration

or noise from pump

a) Leakage in suction pipe.

a) Check and repair 

suction pipe

In the case of 

e)

, 

users shall not 

disassemble 

the pump by 

themselves.

b) Suction pipe is too small or 

suction pipe is partly blocked 

by impurities.

b) Enlarge or check 

suction pipe.

c) There is air in suction pipe 

or pump.

c) Refill liquid to the 

pump and vent air.

d) The comparison of the 

delivery head of device with 

delivery head of pump is very 

low.

d) Improve system or 

choose another pump 

model.

e) Pump mechanically 

blocked.

e) Check and repair 

pump.

Continued

VIII. IMpORTANT NOTICE 

1. Customers will not be advised if this manual is updated. 
2. Pump will be guaranteed for one year under normal operation with the correct  

model. Wearing part is not included. 

3. Users shall be responsible for the damage if they disassemble the pumps by 

themselves in guaranteed period. 

Summary of Contents for HDROO Series










Reviews:

No comments