HYDROO HDROO Series Operation Manual Download Page 2

2

3

DECLARATION OF CONFORMITY 

Machinery Directive: 98/37/EC, 2006/42/EC 

Low Voltage Directive: 2006/95/EC 

Electromagnetic Compatibility Directlve: 2004/108/EC 

Name of manufacturer or supplier

HYDROO PUMP INDUSTRIES, S.L. 

Full postal address including country of origin 

C/ La Banyeta Nova, 11 - P.I. La Banyeta, 17843 Palol de Revardit (Girona) - Catalonia - Spain

Description of product 

HF/HX/HN  is a kind of horizontal multistage non-self priming multistage centrifugal pump.

Name, type or model, batch or serial number 

Name: Light Horizontal Multistage Centrifugal Pump 
Model: HDROO SERIES (HF, HX, HN)

Standards used, including number, title, issue date and other relative documents

Machinery directive 98/37/EC   

 

Ecodesign Directive 2009/125/EC

Machinery directive 2006/42/EC 

 

- Commission Regulation 547/2012

- Standard: EN809:1998 + A1:2009 

 

- Commission Regulation 640/2009 

Place of Issue

 

Palol de Revardit, Spain

Name of authorlsed representative

Miquel Coma

Position of authorlsed representative

CEO

Declaration 

I declare that as the authorised representative, the above information in relation to the supply / 
manufacture of this product, is in conformity with the provisions of the above Dlrectlves. For the 
most specific risks of this machine, safety and compliance with the essential requirements of the 
Directive has been based on elements of the above standards.

Authorized representative

Miquel Coma
CEO

I. AppLICATIONS AND CONDITIONS 

 4

II. DEFINITION OF MODEL 

5

III. CONSTRuCTION 

 6

IV. INSTALLATION AND CONNECTION 

V. START-up, OpERATION AND MAINTENANCE 

11

VI. ASSEMbLE AND DISASSEMbLE 

 12

VII. FAuLT FINDINg AND SOLuTION CHART 

13

VIII. IMpORTANT NOTICE 

 15

CONTENTS

Summary of Contents for HDROO Series










Reviews: