Home
/
HydraMaster
/
CDS 4.6
/
Owner'S Manual

HydraMaster CDS 4.6, Owner'S Manual, Page: 124 / 126

Share

109 pages before
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126

Page: 124 / 126

HydraMaster CDS 4.6 Owner'S Manual Download Page 124

12-1: Warranty Information

12 - Warranty Information

To avoid misunderstandings which might occur between machine owners and the

manufacturer, we are listing causes of component failure that specifically voids warranty

coverage. Such causes listed in this section shall constitute abuse or neglect.

bLOWER

failure to lubricate impellers daily with an oil-based lubricant, to lubricate bearings, to

•

maintain proper oil levels, or to use the correct oil grade and viscosity as recommended
in blower manual.
Failure to properly maintain blower safeguard systems such as waste tank filter screen,

•

vacuum safety relief valve and waste tank automatic shut-off system.
Allowing foam to pass through blower.

•

HIgH PRESSURE WATER PUMP

failure to maintain proper oil level as recommended in pump manual.

•

failure to change oil in pump at recommended intervals.

•

failure to protect pump against freezing.

•

failure to maintain pump protection shut-off system.

•

failure to use water softener in hard water areas.

•

use of improper chemicals.

•

vACUUM TANK

Failure to properly maintain filtering devices in tank.

•

failure to clean tank as recommended by manufacturer.

•

failure to maintain vacuum safety release in tank.

•

use of improper chemicals.

•

CHEMICAL SYSTEM

use of improper chemical.

•

failure to use water softener in hard water area.

•

Operating machine without proper chemical filter screen.

•

failure to protect against freezing.

•

CONTROL PANEL

Failure to protect flowmeter and water pressure gauge against freezing.

•

«
...
122
123
124
125
126
»

Summary of Contents for CDS 4.6































































































































Reviews:

No comments