manualshive.com logo in svg

HydraMaster CDS 4.6, Owner'S Manual, Page: 113 / 126

Share
Download
HydraMaster CDS 4.6 Owner'S Manual Download Page 113

9-5:  electrical System

electrical Troubleshooting

1.0. CDS WILL NOT TURN ON

1.1. The main power fuse 

has blown.

Remove  CDS  cowling  and  engine  cover  and  check  all 

wiring from the power source back to the CDS console 

for damage.  Replace fuse only after locating the problem 

that caused the fuse to blow. If unable to locate problem, 

refer to qualified service technician.

1.2.  The  plug-in  connection 

at  the  base  of  the  recovery 

tank is corroded.

Clean and seal connection to protect it from moisture.

1.3. The main circuit breaker 

has  blown  on  the  CDS 

dash..

Reset breaker and look for loose connections or damaged 

wires.  Check all wires from the control panel forward to 

the  front  of  the  vehicle.  If  no  problem  is  found  but  the 

breaker still trips refer to qualified service technician.

2.0. CDS SHUTS OFF WHILE IN USE

5.1. Recovery tank is full.

empty tank and restart machine.

5.2. Recovery tank float 

switch is dirty or defective.

Inspect  float  to  see  if  the  triangle  mark  on  the  float  is 

facing up.  If it is, and the float slides freely on the post, 

replace the float assembly.

5.3. The vehicle gear selector 

has moved.

Inspect the gear selector to be sure it is in the proper 

position.  If selector has moved, refer to qualified service 

technician.

If  vehicle  gear  selector  has  moved,  refer  to  qualified  service  technician.  This  is  a 

dangerous condition and needs to be repaired immediately.

Summary of Contents for CDS 4.6































































































































Reviews:

No comments