manualshive.com logo in svg

HydraMaster CDS 4.6, Owner'S Manual, Page: 108 / 126

Share
Download
HydraMaster CDS 4.6 Owner'S Manual Download Page 108

   Vacuum Blower System:  8-4

4.0. Noisy Vacuum Blower

4.1.Vacuum blower is low on 

oil.

Inspect oil level and replenish as necessary

Running  the  blower  when  it  is  low  on  oil  will  cause  severe  internal  damage  to  the 

blower.  If this situation occurs, the blower should be inspected by a qualified service 

technician.
4.2. There is internal damage 

to blower.

Refer to qualified service technician.

5.0. Vacuum Blower is locked and will not turn

5.1.The machine has been 

unused for a period of time 

and the blower was not 

properly lubricated when 

it was shut down, causing 

rust to build up on internal 

surfaces.

Spray penetrating oil into blower and let sit for at least 

1 hour. Then very carefully use pipe wrench on outer 

diameter of pulley on blower shaft and attempt to free 

up blower.  Do not use wrench directly on blower shaft. 

If unable to free up blower in this manner refer to a 

qualified service technician.

5.2. There is internal 

damage to blower.

Refer to qualified service technician.

Summary of Contents for CDS 4.6































































































































Reviews:

No comments