Hydac FCU 1310 Operating And Maintenance Instructions Manual Download

Page: 98 / 148

7 | Operation

HYDAC FILTER SYSTEMS GMBH

98 / 148

BeWa FCU1310 3371346g en-us lq

To save your measurements on the USB memory stick, pro-
ceed as follows:

Open the cover to the USB connection by turning it

clockwise (1) and then lift off the cover (2).

Insert the USB memory stick into the USB socket. Note

that the USB memory stick fits into only one position in

the socket.

NOTICE! Do not insert the USB memory into the USB

socket with force.

After inserting the USB memory stick, the FCU will de-

tect it and immediately start copying the measurement

data.

You can see the number of the measurement records to

be copied in the left display (example: 339)

You can detect the number of records in the right display

(example: 4).

Summary of Contents for FCU 1310





















































































































































Search results

Summary of Contents for FCU 1310

Reviews:

Related manuals for FCU 1310

Brands by name

Popular brands

Hydac FCU 1310, Operating And Maintenance Instructions Manual

Search results

Summary of Contents for FCU 1310

Reviews:

Related manuals for FCU 1310

Brands by name

Popular brands