Hydac FCU 1310 Operating And Maintenance Instructions Manual Download

Page: 41 / 148

HYDAC FILTER SYSTEMS GMBH

Putting the FCU into operation | 6

BeWa FCU1310 3371346g en-us lq

41 / 148

6 Putting the FCU into operation

Before operation, the FCU must first be hydraulically and elec-
trically connected, as described below.

6.1 Connecting / disconnecting the power supply

The FCU has a 3-pole socket for connection with a 24 V DC
power supply.

Fig. 15:

Connecting the

power supply

Insert the 3-pole socket plug, e.g. of the power pack,

into the socket until the ratchet can be heard to click in

(

). Connect the other end with the voltage

source.

Once the FCU is supplied with voltage, the display will

show "HYDAC FCU 1###" in ticker format. Afterwards,

the firmware version will be shown for 2 seconds.

The internal sensors will be checked after that.

The display shows

and the

firmware of the sensors.

The self-test is followed in the display by a countdown

The FCU is now ready for the measurement.

As long as the pump is not running and no fluid
is being pumped, the status LED will flash red,

and the display will show

. This

means that there is no oil flow present.

6.1.1 Disconnecting the power supply

To remove the power supply, press the catch (1) on the con-
nector and then pull (2) the connector out.

Summary of Contents for FCU 1310





















































































































































Search results

Summary of Contents for FCU 1310

Reviews:

Related manuals for FCU 1310

Brands by name

Popular brands

Hydac FCU 1310, Operating And Maintenance Instructions Manual

Search results

Summary of Contents for FCU 1310

Reviews:

Related manuals for FCU 1310

Brands by name

Popular brands