Hydac FCU 1310 Operating And Maintenance Instructions Manual Download

Page: 116 / 148

8 | Performing maintenance

HYDAC FILTER SYSTEMS GMBH

116 / 148

BeWa FCU1310 3371346g en-us lq

8.4 High-pressure adapter maintenance

Check or clean the strainer and the flow control valve in the

high-pressure adapter

at regular intervals.

If the required flow through the FCU is not achieved, check
and clean the strainer and the flow control valve in accordance
with the following chapters.

Fig. 50:

High-pressure adapter

8.4.1 Cleaning/changing the strainer

2x Wrench

= 22 mm

1x screwdriver

9x1 mm

or special tool (see chapter

Clean this strainer (B) in the high-pressure adapter at least ev-
ery six months, or more frequently if heavy soiling makes it
necessary.

Fig. 51:

Cleaning / changing the strainer in the high pressure adapter

A Test point

Summary of Contents for FCU 1310





















































































































































Search results

Summary of Contents for FCU 1310

Reviews:

Related manuals for FCU 1310

Brands by name

Popular brands

Hydac FCU 1310, Operating And Maintenance Instructions Manual

Search results

Summary of Contents for FCU 1310

Reviews:

Related manuals for FCU 1310

Brands by name

Popular brands