HYDAC FILTER SYSTEMS OLFCM 10/15 Installation And Maintenance Instructions Manual Download

Page: 54 / 80

8 | Performing maintenance

HYDAC FILTER SYSTEMS GMBH

54 / 80

MoWa OLFCM 3573893a en-us lq

8.3 Changing the filter element - Toploader

In this chapter, you will find the procedure for changing the fil-
ter element.

1x Allen wrench

= 5 mm

1x Allen wrench

= 6 mm

The following steps relate to a

Toploader

filter unit/filter

housing.

Switch the hydraulic system/the unit off and close the

shut-off device at inlet (IN) and outlet (OUT).

Secure the unit from being switched on accidentally dur-

ing maintenance.

Depressurize the filter housing. In order to do so, care-

fully open the bleed screw (Air Bleed) on the filter bowl

cover (

= 6 mm). Do not unscrew the bleed screw

completely.

CAUTION! The operating medium escapes.

Summary of Contents for OLFCM 10/15

















































































Search results

Summary of Contents for OLFCM 10/15

Reviews:

Related manuals for OLFCM 10/15

Brands by name

Popular brands

HYDAC FILTER SYSTEMS OLFCM 10/15, Installation And Maintenance Instructions Manual

Search results

Summary of Contents for OLFCM 10/15

Reviews:

Related manuals for OLFCM 10/15

Brands by name

Popular brands