HYDAC FILTER SYSTEMS OLFCM 10/15 Installation And Maintenance Instructions Manual Download Page 42

Page: 42 / 80

5 | Mounting/installing

HYDAC FILTER SYSTEMS GMBH

42 / 80

MoWa OLFCM 3573893a en-us lq

5.4 Measure or display dynamic pressure / differential

pressure

If pressure is measured in a hydraulic system, the type of mea-
surement such as dynamic pressure or differential pressure
as well as the measurement point is critical, as shown in the
following diagram.

Fig. 10:

Measure or display dynamic pressure / differential pressure

∑p = Total of the pressures

∆p1 = Differential pressure

p1 = Back-pressure

∆p2 = Differential pressure

p2 = Back-pressure

∆p3 = Differential pressure

p3 = Back-pressure

∆p4 = Differential pressure

p4 = Back-pressure

In the example, the back pressure at the first measurement
point shows the total of the subsequent pressures in the hy-
draulic system.

Summary of Contents for OLFCM 10/15

















































































Search results

Summary of Contents for OLFCM 10/15

Reviews:

HYDAC FILTER SYSTEMS OLFCM 10/15, Installation And Maintenance Instructions Manual, Page: 42 / 80

Search results

Summary of Contents for OLFCM 10/15

Reviews: