background image

9

WIJZIGINGEN EN TYPEFOUTEN VOORBEHOUDEN

WIJZIGINGEN EN TYPEFOUTEN VOORBEHOUDEN

Caution:  When the head bore and the column cap are flush, the head cannot be raised further.  Use a ladder to 

observe the column through the top of the belt cover.

8.   Lock the machine head.  Tighten the two head locking bolts (fig. 7)
9.   After the head is set and locked, unlock the collar.  Loosen two set screws (C, fig. 6) 
10.  Slide the lock collar up to the machine head.
11.  Lock the collar.  Firmly tighten two setscrews (C, fig.6). 

Warning: Failure to lock collar can result in damage of the machine and personal injury.

12.  Once the machine head is safely secured, remove the support block
13.  To lower the head, reverse the steps above.  

*Do not loosen the head lock bolts without supporting the head.

Warning!  Failure to lock the head handles can result in damage of the machine and personal 

injury.

7.3  a

djUsTinG

 

THe

 r

acK

 H

eiGHT

To raise the table to a working height requires the raising the column rack.
1.   Lock the table. Use crankshaft (A, fig. 2), clockwise.
2. Unlock column bearing collar (E, fig. 8).  Loosen the two set screws (D, fig.8).

Caution

:  Do not loosen lock nuts (F-fig. 8). 

3.   Raise the rack (G, fig. 8).  Use crankshaft (B, fig. 2), clockwise.
4.   Lock column bearing collar (C, fig. 6).  Tighten the two set screws (D, fig. 8).

Warning: Failure to bearing collar can result in damage of the machine and 

personal injury.

5.   Now the table is free to be raised or lowered for normal operation.

7.4  s

eTTinG

 

THe

 d

epTH

 s

Top

1.   Set the depth to zero by lowering and holding the cutting tools to the surface of the 

work piece.

2.   Unlock the depth scale by turning the lock knob (N, fig. 9)
3.   Set the depth stop by rotating the depth stop knob (P, fig. 9) to the desired depth.
4.   Lock the depth scale by turning the lock knob (N, fig.9)

7.5  o

peraTion

 

cycle

1.   Check that the head is secure.

Warning!  Failure to lock the head handles can result in damage of the machine and personal injury.

2.   Secure the work piece to the table.
3.   Adjust the table to the desired height.  Use crankshaft (B, fig. 2)
4.   Use crankshaft (A, fig. 2) to lock the table lock.  Attach and rotate the 

riser handle clockwise.

5.   Start the machine, press button (A–fig. 1).
6.   Select the transmission mode and spindle speed (F–fig.1).
7.   Select drilling or tapping mode (H–fig.1) and direction of rotation  

(D–fig.1).

Summary of Contents for HU 40 FLOWDRILL TOPLINE























Reviews: