Husqvarna MZ5225ZT / 966690501 Operator'S Manual Download Page 19 | Manualshive

Page: 19 / 64

background image

CONTROls

19

Hour Meter

the hour meter displays the total operating time.
It will flash CHG OIL (Change Oil) at 50 hour intervals.
the flash duration is one hour before and one hour
after the interval. the CHG OIL icon will come on
and shut off automatically. the hour meter cannot be
manually reset.

8058-043

Hour meter

Choke Control

Model MZ5225ZT only

the choke control is used for cold starts in order to
provide the engine with a richer fuel mixture.
For cold starts the control should be pulled out to its
extent.

8058-043

Hour meter

Tracking Knob

If the mower is not tracking straight, check the
air pressure in both rear tires. Recommended air
pressure is 10 psi. (.7 bar) for the front tires and 15 psi
(1 bar) for the rear tires. tracking must be checked on
a flat and level concrete or blacktop surface.
Rotating the tracking knob allows fine tuning
adjustments so the machine tracks straight with the
steering control levers in the full forward position.
Rotate the knob clockwise (as viewed from the
operation position) to increase the speed on the left
lever. Rotate counterclockwise to decrease speed.

8061-010

Tracking knob

«
...
17
18
19
20
21
...
»

Summary of Contents for MZ5225ZT / 966690501

































































Reviews:

No comments

Related manuals for MZ5225ZT / 966690501

Brand: ECLOZ Pages: 60

Brand: Cub Cadet Pages: 32

Brand: Kärcher Pages: 12

Brand: Dolmar Pages: 160

Brand: Sabo Pages: 100

Brand: Simplicity Pages: 4

Brand: Yard-Man Pages: 32

Brand: P1 Pages: 52

Brand: Lastec Pages: 88

23HP Z-Force 60

Brand: Cub Cadet Pages: 32

Brand: Agri-Fab Pages: 16

Brand: Ferris Pages: 24

Brand: Husqvarna Pages: 18

LZ5225 / 965879501

Brand: Husqvarna Pages: 36

Brand: Husqvarna Pages: 32

LZ25 / 968999772

Brand: Husqvarna Pages: 34

Brand: Husqvarna Pages: 32

Brand: Husqvarna Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands