Husqvarna MZ5225ZT / 966690501 Operator'S Manual Download Page 21 | Manualshive

Page: 21 / 64

background image

CONTROls

21

8058-046

Ignition switch - RUN position

Release the key to the RUn position when the engine
has started.

For using “accessory”, turn the key counter clockwise.

Fuses

Fuses are located on the left hand side of the
machine. they are accessed by tilting the seat
forward. Fuses are flat pin fuses type as used in
automobiles.
there are two fuses with ratings and functions:

20 A, Primary fuse

1.

7.5 A, Mower deck coupling

2.

8066-005

Ignition switch - accessory

8050-082

Fuses

«
...
19
20
21
22
23
...
»

Summary of Contents for MZ5225ZT / 966690501

































































Reviews:

No comments

Related manuals for MZ5225ZT / 966690501

Brand: Yard-Man Pages: 36

Brand: MacDon Pages: 55

MT, MTL, MTEFI, MTLEFI

Brand: Walker Pages: 256

Brand: Walker Pages: 96

Electrolux Power Compact

Brand: Flymo Pages: 9

Brand: Ferris Pages: 60

Brand: LawnMaster Pages: 40

Hayterette 005E

Brand: Hayter Pages: 36

Brand: Land Pride Pages: 58

Brand: Gardenline Pages: 34

Derby Stallion ZT2561

Brand: Simplicity Pages: 39

RANSOMES 933304J

Brand: Textron Pages: 28

Brand: Yard-Man Pages: 12

Brand: Baroness Pages: 172

Brand: Yardworks Pages: 24

Brand: MTD Pages: 44

Brand: Weed Eater Pages: 13

SPE131KW, SPE151KW, SPE361, SP

Brand: Snapper Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands