Husqvarna MZ5225ZT / 966690501 Operator'S Manual Download Page 28 | Manualshive

Page: 28 / 64

background image

OPeRaTION

28

WARNING!
Lead-acid batteries generate
explosive gases. Keep sparks, flame
and smoking materials away from
batteries. Always wear eye protection
when around batteries.

Weak Battery

8011-642

Jumper cable connection

IMPORTANT INFORMATION
The mower is equipped with a 12-volt negative
grounded system. The other vehicle must also
be a 12-volt negative grounded system. Do not
use the mower to start other vehicles.

If “jumper cables” are used for emergency starting,
follow this procedure:

Jumper Cables

Connect each end of the ReD cable to the

•

POSItIVe (+) terminal on each battery, taking
care not to short against chassis.
Connect one end of the BLACK cable to the

•

neGAtIVe (-) terminal of the fully charged battery.
Connect the other end of the BLACK cable to a

•

good CHASSIS GROUnD on the mower with the
discharged battery, away from the fuel tank and
battery.

To remove cables, reverse order

Remove BLACK cable first from chassis and then

•

from the fully charged battery.
Remove ReD cable last from both batteries.

•

IMPORTANT INFORMATION
Refer to the EFM Information Sheet from the
unit literature packet for specific jump starting
instructions.

«
...
26
27
28
29
30
...
»

Summary of Contents for MZ5225ZT / 966690501

































































Reviews:

No comments

Related manuals for MZ5225ZT / 966690501

Brand: LawnBoss Pages: 34

Brand: Grasshopper Pages: 56

Lawn Queen 21''

Brand: Jacobsen Pages: 19

Brand: Walker Pages: 92

907254 - LM21SW

Brand: Scotts Pages: 69

Brand: Qualcast Pages: 15

Brand: LAWN STAR Pages: 7

Brand: Webb Pages: 24

Brand: Cub Cadet Pages: 40

Brand: Ryobi Pages: 13

Brand: Ryobi Pages: 48

Brand: Ryobi Pages: 24

Brand: Ryobi Pages: 25

Brand: Ryobi Pages: 348

Brand: Craftsman Pages: 24

Brand: Craftsman Pages: 24

Brand: Craftsman Pages: 27

Brand: Craftsman Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands