manualshive.com logo in svg

Hunter VSX, Operating Manual

Share
Download
Hunter VSX Operating Manual Download Page 13

14

®

To set FCP Inhibit: Press ENTER at the 

“Set FCP

Inhibit?”

 display. The display will then show:

The current selection will be capitalized (de-
fault is 

OFF

). The 

“on” 

selection will be in

lower case. Press the TOGGLE button to switch
between 

OFF

 and 

ON

. When it is correct, press

ENTER. The display will flash 

“SAVED!” 

and

your selection. After a moment, the display will
revert to:

You may now press the OPTIONS, BACK or
NEXTbuttons to view more options, or you may
press EXIT to leave the Edit Settings mode.

Set Response?: This will set the level of Field
Controller response to the central computer (if
it is present and communicating). In the Partial
Response setting, the field controller will report
any alarm conditions (such as Fuse Open,
Overload, Power Outage, etc.) if they occur.

In the Full Response setting, the Field Control-
ler will report all events as they occur, includ-
ing every station start and station stop, as well
as alarms. Full Response will also continuously
update the Station Status Display on the central
computer.

If full reports are not desired, or cause too
much communications “chatter”, you can set
this to Partial.

To set Response: Press ENTER at the 

“Set

Response?”

 display. The display will then show:

The current selection will be capitalized
(default is 

PARTIAL)

. The 

“full”

 selection will

be in lower case. Press the TOGGLE button to
switch between 

PARTIAL

 and 

FULL

. When it

is correct, press ENTER. The display will flash

“SAVED!”

 and your selection. After a moment,

the display will revert to:

You may now press the OPTIONS, BACK, or
NEXT buttons to view more options, or you may
press EXIT to leave the Edit Settings mode.

Set MR Runtime?: MR = Maintenance
Radio. This determines the time-out timer
setting for stations started by Maintenance
Radio without specified Run Times.

If you simply start a station with Maintenance
Radio without a specific run time (see Sending
a Maintenance Radio command on page 41)
and forget to turn it off, this setting will auto-
matically shut it off after the time shown, to
prevent flooding and damage. The default
value is 30 minutes. You may select a longer or
shorter setting, from 1 minute to 18 hours, for
this safety feature.

To set MR Runtime: Press ENTER at the

“Set MR Runtime?”

 display. The display will

then show:

Type the number for the default Maintenance
Radio timer (example: 20 minutes) with the

Summary of Contents for VSX
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands