manualshive.com logo in svg

Hunt Electronic HVRM-S400E, Installation Manual

Share
Download
Hunt Electronic HVRM-S400E Installation Manual Download Page 8

 

8 

- Each input line can be switched by a relay contact from devices such as pressure pads, passive infra-

red detectors, smoke detectors and similar device. You can configure the alarm inputs as N/O (Normal 

Open)or N/C (Normal Close) in the menu system. The default is N/O. 

6. Connect up to four alarm output relays via the terminal connector. 

      - Relay 1 responds to an input alarm, Relay 2 responds to a system failure and the other relays are   

assigned to the remote software. Configure the alarm output as N/O or N/C in the menu system. 

7. Connect to your network via the Ethernet port. 

      - The HVRM-S400E is delivered with the DHCP function switched on, so IP address are assigned 

automatically if the network server uses DHCP. (Refer to the System settings/Connectivity/Network setup 

menu) 

 

Powering up 

8. Switch on all connected equipment. 

9. Connect the power cord to the unit and switch on. 

 

 

 

 

<Note> 

 

Be sure to use a DC adapter that is provided by HUNT ELECTRONIC USA INC. 

Power (applied adaptor) : 

12Vdc 5A (110V ~ 220V) 

 

 

 

 
 

 

Summary of Contents for HVRM-S400E


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands