manualshive.com logo in svg

Hunt Electronic HVRM-S400E, Installation Manual

Share
Download
Hunt Electronic HVRM-S400E Installation Manual Download Page 39

 

39

 

 

>> DELETE VIDEO 

•    Data can be deleted from a designated time frame. This can be set from the beginning of the recorded   

data (fixed) to a user defined time.   

•    Select the date and time up to which the recorded data is to be deleted and then select Delete 

 

>> STORAGE SETUP 

•    The storage setup menu provides a way to enable or disable internal hard disks and to view the status of   

connected hard disks.   

•    Disk shows the internal disk that has been detected.   

•  Size indicates the disk size of each disk in GB.   

•    Set Enabled to either Yes and No to enable or disable a disk. If a disk is disabled, a message warns you   

that disabling a disk causes data loss. A new hard disk can be formatted if Enabled is set to Yes.   

•    Status indicates the status of the disk. OK indicates that the disk is operating correctly and can be used   

for recording; Fail indicates a problem 

 

>> STATUS OVERVIEW   

•    The status overview menu provides information on the status of the connected hard disks.   

•    Earliest/Latest Recording indicates the times of the earliest and latest recordings on the disk.   

•    Disk capacity indicates the total hard disk size in GB.   

•    Used space indicates the hard disk space that has been used by recordings 

 

5.

 

Connecting external device with serial port 

 

 

 

 

 

 

Summary of Contents for HVRM-S400E


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands