manualshive.com logo in svg

Hunt Electronic HVRM-S400E, Installation Manual

Share
Download
Hunt Electronic HVRM-S400E Installation Manual Download Page 31

 

31

 

>>> SEQUENCE DWELL TIME   

•    Specify the sequence dwell time that is used when the SEQ key is pressed.   

•    The interval can be configured with a slider from Off (disable) to 60 seconds (default 10 seconds).   

 

>>> EXIT PLAYBACK ON EVENT   

•    When set to On, the HVRM-S400E exits playback to display a live event. 

 

>>> VGA MODE 

•    VGA mode can be changed to 4 different modes. 

800 x 600 @ 56  /  800 x 75 @ 75  /  1024 x 768 @ 60  /  1280 x 1024 @ 60 

 

>>> Playback Deinterlace 

•  Deinterlace enable / disable

 

The “Deinterlace Mode” only runs when the recording resolution is in Full D1.   

In case of enable it, the Full D1 image with Pause condition the picture will have less tremor.   

In case of keep press the Pause button continuously from Pause condition, the “Deinterlace Mode” can   

be On/Off in Toggle condition.   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for HVRM-S400E


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands