Humminbird 700 SERIES 786CI Operation Manual Download Page 51

Page: 51 / 138

attiin

g S

offttw

arre

Software updates can be added to your Chartplotter. Go to the Humminbird®
web site for information and computer requirements at

www.humminbird.com

or call

1-800-633-1468

In addition to your Chartplotter and personal computer with Internet access,
you will need one of the following optional-purchase accessories:

•

MMC Card Reader (AS CR)

OR...

•

PC Connect Cable (AS PC2)

Updating Software requires the following top-level steps:

1. Log on to

www.humminbird.com.

•

Download HumminbirdPC

™

to your computer.

2. Once you have registered your Chartplotter, you can access software

downloads from your online profile.

3a. MMC/SD Card: Follow the instructions provided with the MMC/SD

Card Reader to connect the MMC/SD Card Reader to a personal
computer and download the software update.

• Install the MMC/SD card with the updated software file into your

control head.

•

Power on your control head. The Chartplotter will recognize the
new software and run through a series of prompts to confirm
software installation.

OR...

3b. PC Connect Cable: Follow the instructions included with the PC

Connect Cable to connect your Chartplotter to your computer.

NOTE:

The MMC/SD Card Reader and PC Connect cable require a separate

purchase. For more information, visit our web site at

www.humminbird.com

contact our Customer Resource Center at

1-800-633-1468

Multi-Media Card (MMC)/SD Slot

Summary of Contents for 700 SERIES 786CI











































































































































Search results

Summary of Contents for 700 SERIES 786CI

Reviews:

Related manuals for 700 SERIES 786CI

Brands by name

Popular brands

Humminbird 700 SERIES 786CI, Operation Manual

Search results

Summary of Contents for 700 SERIES 786CI

Reviews:

Related manuals for 700 SERIES 786CI

Brands by name

Popular brands