Hughes Strigo 4201 Page 36 User Manual Download

Page: 36 / 40

Chapter 6

•

Technical specifications

H61798

Revision E

Chapter

Technical specifications

Item

Specifications

Weight

2 kg

Dimensions

233 mm x 293 mm x 51 mm

Humidity

95% RH at 40 °C

Power, Max

57 W (when transmitting)

Water/Dust

IP-54

Operating Temperature

-5 °C to +40 °C with battery

-25 °C to +55 °C excluding battery

Storage Temperature

-40 °C to +60 °C with battery

-40 °C to +80 °C excluding battery

Battery Charging Temp

0 °C to 40° C

External Power Supply

Hughes AC/DC Adapter

Wind Loading

40 km/h with stand secured

Other Features

Rechargeable lithium ion battery

USIM/ISIM slot behind battery

Mounting point on terminal

Compass to assist pointing

Note:

The Hughes 4201 mobile satellite terminal operates on DC power which can

be supplied by an AC or DC power source. To comply with safety
requirements, the terminal must be powered with an AC/DC adapter or DC
power adapter supplied or approved by Hughes.

Summary of Contents for Strigo 4201









































Search results

Summary of Contents for Strigo 4201

Reviews:

Related manuals for Strigo 4201

Brands by name

Popular brands

Hughes Strigo 4201, User Manual

Search results

Summary of Contents for Strigo 4201

Reviews:

Related manuals for Strigo 4201

Brands by name

Popular brands