![Hudson 1948 Commodore Service Manual Download Page 9](http://html1.mh-extra.com/html/hudson/1948-commodore/1948-commodore_service-manual_2181507009.webp)
BODY MANUAL 4
INSTALLATION
To install, reverse procedure of removal.
DOOR GLASS - REAR
(All Models 1948 thru 1954
Except 1C, 1D, 2C, 2D and 3D)
REMOVAL
1. Remove safety lock knob and garnish moulding.
2. Remove small wood block.
3. Run glass to within 2" of the top. and pull inward on top of
glass to release glass from glass runs.
4. Tip glass inward and raise window until glass channel can
be released from regulator.
5. Remove glass and glass channel.
INSTALLATION
1. Insert channel and glass through opening and engage regu-
lator.
2. Run regulator up and down to work glass into position.
3. Replace wood block.
4. Replace garnish moulding and safety lock knob.
DOOR GLASS - REAR
(Models 1C, 1D, 2C, 2D and 3D)
REMOVAL
1. Remove door trim panel. See "Trim Panel Removal", Page
1.
2. Cut inner liner as shown in Figure 5, to expose screws (J).
3. Remove the two screws (J) attaching center bar glass run to
door inner panel.
4. With the door glass in the down position, remove the
retainer clips from the regulator arm.
5. Remove regulator arm from glass channel and bring the
door glass down, at the same time, turn glass 1/4 turn to bring
the narrow side of the glass to the top. Tilt glass inward and
remove glass and glass channel through the top opening in
door.
I
NSTALLATION
To install, reverse procedure of removal and repair any
damage to door inner liner.
DOOR VENTILATOR WING
-
FRONT - CRANK TYPE
(All Models 1948 thru 1954
Except 1C, 1D, 2C, 2D and 3D)
REMOVAL
1. Remove safety lock knob and garnish moulding.
2. Remove ventilator regulator handle and valance.
3. Remove garnish moulding spacer wood block.
4. Cut hole in door inner liner as shown at (B) in Figure
7, to expose clevis (G) connecting wing to regulator and
remove screw from clevis.
5. Open ventilator wing and press down on top of frame
to release it from upper pivot and lift out ventilator.
FIGURE 7
INSTALLATION
Reverse procedure of removal. Make sure ventilator
weatherstrip lip is over garnish moulding. Repair inner
liner.
Summary of Contents for 1948 Commodore
