35 BODY MANUAL
QUARTER WINDOW REGULATOR
BROUGHAMS AND COUPES
(All Models 1948 thru 1954
Except 1C, 1D, 2C, 2D and 3D)
REMOVAL
1. Remove quarter trim panel. See page 33.
2. Remove quarter panel inner liner.
3. Remove quarter window glass.
4. Remove four Phillips head screws attaching regulator to
inner panel and remove regulator through lower opening in
inner panel.
INSTALLATION
Reverse procedure of removal.
QUARTER WINDOW GLASS
BROUGHAMS AND COUPES
(All Models 1948 thru 1954
Except 1C, 1D, 2C, 2D and
3D)
REMOVAL
1. Remove garnish moulding and small wood block.
2. Lower window and release three clips attaching glass run
channel to top of window opening by pulling in on channel.
3. Remove glass run channel.
4. Pull in on top of glass and raise glass to limit of regulator.
5. Release regulator from glass channel and remove glass and
channel.
INSTALLATION
1. Pull in on top of inner panel to enlarge opening between
inner and outer panels.
2. Insert glass and glass channel through opening and engage
regulator.
3. Lower the window and apply a coating of cement to
window opening to seal glass run channel.
4. Insert glass run channel and engage clips in top of window
opening.
5. Raise window and replace wood block and garnish mould-
ing.
QUARTER WINDOW GLASS
BUSINESS COUPES
(All Models 1948 thru 1954
Except 1C, 1D, 2C, 2D and 3D)
REMOVAL
1. Remove garnish moulding.
2. Remove small wood block.
3. Remove two screws holding window support to inner
panel. Hold window in position and remove support.
4. Lower glass to free it from glass run channel and lift out.
INSTALLATION
Reverse procedure of removal.
QUARTER WINDOW GLASS
SEDANS (PIVOT TYPE)
(All Models 1948 thru 1954
Except 1C, 2C, 1D, 2D and 3D)
REMOVAL
1. Remove garnish moulding.
2. Remove f our sheet metal screws attaching glass frame
to window opening and remove glass and frame.
3. Remove nut and spring from friction pivot.
4. Remove screw from upper pivot and remove window
and frame.
INSTALLATION
Reverse procedure of removal.
QUARTER WINDOW GLASS
SEDANS (PIVOT TYPE)
(All Models 1948 thru 1954
Except 1C, 2C, 1D, 2D and 3D)
REMOVAL
1. Remove the three sheet metal screws attaching garnish
moulding to window opening.
2. Push glass inward and remove glass, weatherstrip and
frame.
Summary of Contents for 1948 Commodore
