2. If it is necessary to adjust the door window, loosen the two
screws (J), Figure 201, and slide window up or down as
required.
NOTE: These 7/16" Hexagon head bolts are accessible
through the holes provided in the inner panel at (J). These
bolts need only be loosened as the tabs on the lower glass
rest channel are slotted.
DOOR WINDOW REGULATOR
CROSS ARM ASSEMBLY
REMOVAL
1. Remove door inside hardware and trim.
2. Cut inner panel along remote control arm to expose screws
(N), Figure 194.
3. Remove screws (N), lower window to bottom of door and
release regulator cross arms from door glass channel.
4. Disconnect regulator arm from cross arm assembly by
removing the spring clip retainer.
5. Remove regulator cross arm assembly through opening in
bottom of door.
INSTALLATION
To install, reverse procedure of removal.
DOOR VENT WING
1. Remove door inside hardware and trim.
2. Remove the vent wing mounting bracket screws (E),
Figure 194.
3. Remove the wing pivot to vent wing regulator screw (F).
4. Remove screws (G) and (H) attaching door w in g frame
and door window front guide channel to inner panel.
5. Lift door wing assembly up and out of door.
INSTALLATION
1. Insert door vent wing and frame assembly so that the
lower pivot fits into the regulator shaft.
2. Insert pivot to regulator screw (F). 3. Insert, but do not
tighten, screws (E) and (G).
4. Raise door window and check alignment with the door
window. Then tighten screws (E) and (G).
5. Insert and tighten screw (H). See "Vent Wing Adjust-
ment", before installing trim and hardware.
DOOR VENT WING REGULATOR
REMOVAL
1. Remove the inside hardware and trim.
2. Remove the pivot to regulator arm screw (F), Figure 194.
3. Remove the two regulator to inner panel mounting
screws (1) and remove the regulator down through for-
ward end of the door and out through bottom opening in
inner panel.
INSTALLATION
To install, reverse procedure of removal.
DOOR VENT WING
ADJUSTMENT
1. Remove the two vent wing mounting bracket screws (E),
Figure 194.
2. Loosen screw (G) and remove screw (H).
3. To tilt the vent wing frame assembly inward, insert a
washer or washers between the wing support and the
inner panel at the upper attaching screw (E). (To tilt
frame outward, insert washers at lower screw (E).
NOTE: Tilting the glass inward moves the bottom of the
center glass channel away from the inner panel. Washers
should be inserted between the lower end of the channel
(H) and the inner panel to hold channel in position.
4. Retighten screws (G) and (H).
NOTE: Top of door vent wing must solidly contact door
opening upper weatherstrip. To adjust, reposition screws
(E) and bend bracket (H) upward as required.
If complete frame does not contact rubber weatherstrip,
loosen door hinge screws and raise complete door. Recheck
door adjustment and door window adjustment.
BODY MANUAL 130
Summary of Contents for 1948 Commodore
